Principles of heat pump dryer
Heat pump drying units by compressor, heater (condenser), throttling device (electronic expansion valve), heat absorber (evaporator) four parts constitute a circulation system, using the reverse carnot principle to absorb the nature in the air and the heat transfer to the heat drying room, causes the temperature of the drying room to rise, the moisture evaporation from material to achieve the purpose of material to water and dry.Mainly used in low temperature (below 10 ℃ temperature ring) drying operation of region, by recycling water vapor heat drying material for material drying. So the drying operation is not subject to external temperature, drying process of the volatile components of the material can be recycled: such as rose drying unit condensate water for rose dew production.
◪ Dehumidification, drying, refrigeration, dehumidification, ventilation and ventilation are integrated intelligent drying and dehumidification equipment.
◪ Easy to use, closed dehumidification and heat pump drying method are adopted to save energy and reduce emission. Compared with the traditional belt type hot air dryer, the energy saving is more than 40% and that of the microwave belt type dryer is more than 60%.
◪ Suitable for all kinds of drying under 70 ℃ temperature desiccant dehydration mode, dry and stable, good quality, health.
◪ The unit automatically adjusts the drying time and temperature according to the requirements of multi-temperature drying process, and intelligently controls the temperature and humidity curve program.
◪ Meet the requirements of large temperature difference and gradient temperature pipeline drying process.
Introduction to compressor
American imported brand gulun scroll compressor, high energy efficiency is more than 12% higher than the general piston compressor, good reliability, liquid impact resistance, high tolerance of impurities, low noise, small vibration.
Sheet metal shell introduction
1.2-1.5 thick anticorrosive steel plate with strong ability of preventing salt alkali and acid is used. Outdoor protective coating is sprayed on the surface to make it beautiful and good-looking.
Fan introduction
Iron case iron wind blade waterproof copper wire motor, with quiet, stable air volume, less vibration, eliminate the plastic fan blade rupture, deformation risk.
Introduction to evaporator
Hydrophilic, corrugated aluminum Bernstein and internal screw copper tube heat exchanger. High heat transfer efficiency and durability. The hydrophilic property makes the condensed water on the heat exchanger drain away quickly.
Introduction of Electronic Control System
Man-machine interface control system, 7-inch touch screen operation screen, simple and clear use, can set 10 different operating parameters of the time period, heating, dehumidification, dehydration, humidification and other different working modes freely set, operating parameters, curves at any time query.
Introduction to fluorine circuit and valve
Fluorine valve body adopts Japanese heron palace, Emerson throttle valve, accurate opening, little leakage, ultra-low failure rate! All fluorine welding joints are welded with 5% silver solder, good toughness, strong welding joints, no cracking.
Introduction to high efficiency waste heat recovery core
To further recover the heat of external drainage of moisture, improve the heat production of the unit, increase the capacity of moisture drainage, reduce heat loss.
Introduction of screws
All fasteners are made of 304 stainless steel screws, never rust, easy to maintain high grade and beautiful folding!
Introduction to chassis
Each product adopts channel steel Qi whole welding, surface spraying outdoor protective coating, solid and firm, durable.
The fan is introduced
High temperature and humidity resistant fan, safe and reliable, long service life, adequate air volume, less dead Angle.
Introduction to dehumidification valve
Adopt automatic adjusting exhaust valve, automatic dehumidification, can automatically adjust the amount of dehumidification according to the drying state.
Introduction to temperature and humidity sensor
According to the characteristics of drying materials can be independently selected dry/wet ball moisture meter or electronic moisture meter.
Model | KB-380E | KB-750E | KB-1500E |
Rated heating capacity (KW) | 20 | 35 | 80 |
Power supply | 380V | 380V | 380V |
Rated power (KW) | 6.5 | 11 | 22 |
Rated current (A) | 13 | 22 | 44 |
Maximum power (KW) | 8 | 14 | 28 |
Maximum current (A) | 16 | 28 | 56 |
Rated moisture removal (Kg/h) | 18 | 30 | 72 |
Rated drying temperature (℃) | 60 | 60 | 60 |
Maximum drying temperature (℃) | 75 | 75 | 75 |
Ambient temperature (℃) | -15-40 | -15-40 | -15-40 |
Host quality (Kg) | 280 | 540 | Customize |
Host size (length * width * height) | 950*950*1780 | 1290*950*1780 | Customize |
Supporting electric auxiliary heat (KW) | 12 | 12 | 12 |
Working pressure (MPa) | 3 | 3 | 3 |
Noise (dB(A)) | 65 | 65 | 65 |
Heat pump drying units is applicable products, dehydrated vegetables, black and white fungus, melon seeds, peanuts, fruits and vegetables, meat products, casing, tobacco, leather, mushrooms, Chinese wolfberry, dried fruit, mosquito-repellent incense, GongXiang, fabrics, clothing, food grains, noodles, bean curd stick, fertilizer, medicine, traditional Chinese medicinal materials, paper, wood, seeds, sludge, gypsum, hardware products, metallurgical products, mining products, chemical products, flue gas desulfurization gypsum, clay, grass, flue-cured tobacco, pulverized coal, the coal and lignite drying.
Contact
Supplier