Door frame and elevator hall decoration works elevator door wall cladding

Modern and simple design stainless steel metal screens & partitions decorative hotel partitions and home room divider 

Door frame is a kind of architectural decoration term, which refers to two door frames inside and outside the door. There are also directly called door frames. Its main function is to fix the door leaf and protect the corner, decoration and so on. Commonly used in the decoration process, to protect the door from scratch, corrosion, damage, dirt and so on. Stainless steel door frame, more popular is the door wrapped with a layer of high - quality stainless steel

The commonly used stainless steel plates are divided into 201 and 304 models. In fact, the ingredients are different. 304 is better in quality, but expensive in price. 201 is a little worse, but it can fully meet the needs of household use. In addition, the thickness of the plate is also different, the general quotient after the actual 0.6mm is enough.

There are two styles of stainless steel door frame. One is that the vertical and horizontal edges adopt 45 degree angle, and the other is vertical installation of vertical and horizontal edges. It is recommended to use the latter one. Sometimes the former needs to weld the angle, which is very troublesome and the effect is not good.

Installation: if it is a traditional way - door frame made on site, it is directly fixed to the door pocket body of the door opening wall by the decoration workers on site; if it is the door frame installation of a complete set of door products.

First, whether the technical structure of the door pocket of the corresponding complete set of door products conforms to the three technical characteristics of firmness, accuracy and stability required for a complete set of door products;

1. Check the specification, opening direction and relevant accessories of the door according to the design drawings.

2. Measure the height and width of the door opening with a tape measure. In China, the standard height and width of the room door is 200cm × 80cm; the height and width of the toilet door is 200cm × 70cm. If there is any discrepancy in size, it should be corrected in time.

3. Measure the position line, determine the position of the door frame, draw out the vertical line with ink fountain, and two vertical lines of the door opening on one side

4. We refer to Chinese domestic practice. The distance between the holes is about 30cm. There are 10 holes in two rows of one side door. The bit of impact drill should be 12mm and the depth of the hole drilled is about 6cm

5. Hammer small wooden wedges into the holes one by one to fix the door frame panel. The size of the wedge is 5cm × 1.5cm × 1.5cm, which is better made by larch, because the wood structure of larch is tight and not easy to loosen

6. Open material to make door frame. The dimension of the wood board for the keel of the door frame on both sides is 200cm × 3cm × 8cm, and the dimension of the wood board for the keel of the door frame top is 80cm × 3cm × 8cm. Glue the high-density 9cm board on the keel and fix it with air gun nails.

7. connect the three door frames according to the shape of the door, and fix them at the joint with big nails.

8. Put the door frame on the door opening, according to the horizontal line of the wall, pad up the door frame with wood or brick under the door frame, and adjust the height of the door frame. 5cm is reserved below and buried in the keel of the floor.

9. Put the door frame on the door opening, according to the horizontal line of the wall, pad up the door frame with wood or brick under the door frame, and adjust the height of the door frame. 5cm is reserved below and buried in the keel of the floor.

10. Make the line of the door face. The front door can be bought off the shelf or made by the construction personnel according to the drawings. After the production is completed, the door face is fixed to the door frame, so the door pocket is basically completed. 

11. Make the line of the door face. The front door can be bought off the shelf or made by the construction personnel according to the drawings. After the production is completed, the door face is fixed to the door frame, so the door pocket is basically completed.

12. Put the door on the door frame, make sure the specific position of the hinge on the door pocket, and then cut out the caliber according to the thickness of the hinge. Also cut out the diameter of the lock sleeve. Install the door to the door pocket, and fasten the Gong screw with a gong wire cutter on the hinge. Note that the gap between the door and the door pocket shall not be greater than 1.5mm, which shall be subject to the smooth opening and closing of the door.