Vacuum Moulding Machine

*Send an Inquiry to this supplier

Supplier Info.

Company Name： Shantou Mengxing Package Machinery Co.,Ltd.

Registration Date： 1998

Country / Region： guangdong / China

City： shantou

Main Products： vacuum forming machine,plastic vacuum forming machine,automatic cutting machine

Product Detail

Basic Info.

Model NO.

XCH130/110/13.5

Trademark

MengXing

Specification

4200 * 2410* 2900mm

Origin

China

HS Code

84775900

I,Work principle
Using the thermoplastic sheet is heated and softened in the mold for vacuum molding, become necessary products. Their work is the clip - heating - forming - products.

II,Features
01. Mechanical, pneumatic, electrical integration. Each action program controlled by the PLC. Touch-screen operation, simple and convenient.
02. Loading easier, less scrap molding material savings.
03. Heater motor, frequency control, high-speed accurate and stable.
04. Electric furnace temperature control system is fully computerized intelligent automatic compensation control, partitioning a controlled man-machine interface of a digital input, with high precision fine-tuning, temperature uniformity, fast heating (just five minutes from 0-400 degrees), stable ( influence from external voltage, temperature fluctuations of not more than 1 degree), low energy consumption (saving about 15%), long life plate stove, electric bricks etc. automatically detected.
05. Suitable convex molding, molding height, stable product quality.
06. The mold seat with electric limit adjustment, adjust quickly and easily.
07. Device is equipped with air-cooling system that allows products to cool faster and better styling.
08. Production counts, or can be set to automatically shut down ahead of the police, with file memory function, can store up to 230 product parameter data
09. The die table using mosaic lubricated bearings, freedom of movement and accurate.
10. Die clip structure movements and synchronized by the rack and pinion structure linkage, the lifting synchronization, extending cylinder life
11. Operating side using safety grating devices to ensure the safety of the operator misuse.

III,Technical parameters

Parameter		XCH130/110/13.5(mode No.)
Max. forming area (mm2)		1300mm*1100mm
Min.forming area (mm2)		1200mm * 1000mm
Sheet specifications (Max.)		1370mm * 1170mm
Thickness of sheet applied		0.8-3mm
Max. molding height		135mm
Capacity		1-3 (times/min)
Gas source	Air consumption (m3/min)	≥ 2
	Pressure	0.6Mpa(inlet 0.8-1Mpa)
Vacuum pump (Outlay)		Busch R5 0100
Power		three-phase four-wire 380V / 220V 50Hz
General power		64KW
Dimensions ( L × W × H) (mm)		4200 * 2410 * 2900
Total weight (Kgs)		4000

IV,Technical configuration

Programmable logic controller (PLC)	Taiwan Delta
Touch screen monitor (10.4 "inch / Color)	Taiwan Delta
Inverter	Taiwan Delta
Feeding motor	China
Heater (99pcs)	China
Solid state relay AC contactor	Germany Siemens
Thermo relay	Japan Omron
Vacuum pump	Busch R5 0100
pneumatic components	South Korea
Cylinder	China
Fan blower	China

V,Installation Instructions
1. The machine should be installed in a dry, clean shop floor. And leave some aside installation location of the active working distance gas, electricity, refer to the machine diagram of a flat position.
2. After removing the packaging machine, placed on the ground level of the firm can use. Its area, see the appearance of space dimensions Figure II.
3. Were connected to a source of water and gas supply, and connect the ground wire.
4. Check heater heating elements are intact (Ruoyin shipping damage should be replaced).
5. All lubrication points should be added to lubricants. Vacuum pumps, air source FRL oil level should come on to the line. The watershed of the filter device slop put the net.
6. Check the vacuum pump motor, cooling fan rotation is correct (after power test, which if not properly swap two wires can).
7. Supply part of the user's machine to install their own gas purification equipment, in order to ensure increased service life of pneumatic components. Please refer to the pneumatic equipment clean air system flow chart diagram III.
8. External power cable with double insulated copper wire 4, each section is not less than 16mm2.

VI,Sample Picture
Vacuum Moulding Machine

VII,Certifications

VIII,Workshop Pictures

IX,Package
Vacuum Moulding Machine

X,Exhibition
Vacuum Moulding Machine

This product has applications in a wide range of fields. Each action program of the product is controlled by the PLC. It is estimated that the product has a long service life in the market. Each action program of the product is controlled by the PLC.

Contact

Supplier

Tell us your Buying Requirements