1.Characteristics:
. YT935 is a kind of one-component acid solidifying high performance silicone sealant with high strength,fast solidification,semitransparent and no discoloration.
. Good for the adhesion of glass and ceramics.
. Good anti-aging property.
. Outstanding anti-high temperature property change in property is little within the scale of -40℃~150℃.
2.Purpose:
. Glass installation and fixation.
. Gap sealing of glass.
. Structural fixation of point-supported and full transparent glass curtain wall.
. Adhesion and sealing of technological glass structural project of day-lighting roof.
3.Typical Technology Data
No. | Performance | Standard | Measured value | Single Evaluate | |
1 | Appearance | Fine and uniform ointment,it shall not have block gel, surface coagulation and educt that cannot disperse quickly. | Conform standard | Qualified | |
2 | Slumpability(mm) | Vertical,(mm) | ≤ 3 | 1 | Qualified |
Horizontal | Non distorted | Non distorted | |||
3 | Extrusion,(ml/min) | ≤ 10 | 1.6 | ||
4 | Tack-Free Time(h) | ≤ 180 | 50 | Qualified | |
5 | Harducss(HA) | 20~60 | 29 | Qualified | |
6 | Tensile strength in adhesion standlard conaition | Tensile strength in adhesion (Mpa) | ≥ 0.345 | 0.652 | Qualified |
88℃ Tensile strength in adhesion | Tensile strength in adhesion (Mpa) | ≥ 0.345 | 0.642 | Qualified | |
-29℃ Tensile strength in adhesion | Tensile strength in adhesion (Mpa) | ≥ 0.345 | 0.638 | Qualified | |
Adhesion of immersion in water | Tensile strength in adhesion (Mpa) | ≥ 0.345 | 0.708 | Qualified | |
7 | Loss of heating% | ≤ 10 | 3.9 | Qualified | |
Stability | Store for 9 months at -20~27℃ in cool ,dry places after date of delivery |
4.Application Standard:
. National Standard GB/T14683-2003
. Enterprise Standard Q/(NGS)YT 1-2005
. ISO9001:2008
5.Package:
. 310mL plastic tube package (Net capacity: 300mL).
6.Restriction of Usage:
YT935 Point-supported Glass Curtain Wall Sealant cannot be used in the following situations:
. Hidden or Semi-hidden Framing Glass Curtain Wall
. All materials that may exude oil and fat, plasticizer or solvent.
. Closed places.
. Frosting or wet surface.
. Continuous water soaking places or places that are wet all the year round.
. Fixation of metallic coated glass.
. Places contacting with alkaline matters as marble and granite stone etc..
. Construction should not be carried out in case the surface temperature of the materials is under 4℃ or over 40℃.
7.Technical Service:
. Providing with full technique information of the product .
8.Joint Design and Working Procedure:
. Please refer to the Technical Use Guide of Structural Silicone Sealant of Yuantong Company.
9.Safety:
The product is nontoxic after solidifying completely.Touch with the eyes should be avoided before solidification.In case this happens, please wash the eyes with water and go to the doctor for help;Children should be kept away from the un-solidified product.Low molecular compounds may be released during the solidification of silicone sealant, thus attention in ventilation should be paid in the construction and solidification areas with a view to avoid negative effects to human body caused by these compounds for over high concentration.
10.Estimation of Dosage:
Remark:The actual dosage of silicone sealant may be different from interface design, installation place of gasket material, dressing technology and amount of wastage on site.
Please refer to Table 1 for the estimated dosage of YT935 special point-support curtain wall sealant needed by various specification interfaces.
Table 1 Construction Length of Each Yt935 (300ml) Silicone Sealant
Thickness(mm) | Width mm | ||||||
6 | 9 | 12 | 15 | 18 | 21 | 24 | |
6 | 8.3 | 5.5 | 4.2 | 3.3 | 2.8 | 2.4 | 2.1 |
9 | 5.5 | 3.7 | 2.8 | 2.2 | 1.8 | 1.6 | 1.4 |
12 | 4.2 | 2.8 | 2.1 | 1.7 | 1.4 | 1.2 | 1 |
11.Time for Solidification:
Solidification reaction begins from the surface to the inside once YT935 is extruded and contacts with the air.The surface dry time is about 30 min and the greatest adhesive strength would appear after 21 days after it is completely solidified.
Contact
Supplier