LCD frozen separator machine for repairing mobile phone, laptop, IPad LXPB-360*260

Frozen separator machine, LCD/OLED freezing separator with minus 160/180 degrees, LCD/OLED freezer separator, Samsung LCD/OLED freezer separator, 

Broken screen freezing separation, High ambient temperature resistant LCD freezer separator, On-board screen freezing separation, 

Mobile phone screen freezer separation, Mobile phone glass is separated from the LCD/OLED, Ultra-low temperature refrigerator, 

Plate screen/Laptop freezing separation, 13/17/17.3/18 inch freezer separator

PRODUCT FEATURES       

At present, there are 3 kinds of methods (molybdenum wire cutting, liquid nitrogen freezing and refrigerator freezing) which are regularly used in LCD screen reworking industry. 

The efficiency of the molybdenum wire cutting method is very low and the relevant yield rate of LCD refurbishment is also very low.

If users adopt liquid Nitrogen to separate the LCD screens, the consumption of liquid Nitrogen is too large and LCD screen explosion phenomenon will occur at any moment. On the other hand, injury hidden danger exsits on the liquid Nitrogen during the LCD screen separating process.

Compared with the above mentioned 2 methods, LXBX series ultra low temperature frozen separator machine has many advantages in the LCD screen separation field. Its later use-cost is much lower than liquid Nitrogen, and it is also much more convenient and safer. In view of these advantages, LXBX series ultra low temperature frozen separator machine has been adopted by many LCD manufacturers and LCD maintenance enterprises because of its high yield rate of LCD refurbishment, low use-cost, no danger and other excellent characteristics as follows: 

1.) Ease of operation, one-button start, high precision intelligent temperature control system, rapidly reach to the preset temperature.

2.) Imported advanced refrigeration compressor and accessories, can run continuously for 24hours, more stable refrigeration performance.

3.) Equipped with double sealing treatment top opening door and super thick thermal insulation layer box body, excellent thermal insulation performance, effectively reduce the loss of cooling capacity and greatly ensure the working temperature, energy saving, easy to operate.

4.) Safety electricity protection system equipped with ground wire, over heat protection, short circut protection, over current protection, high & low voltage protection, reverse phase lack protection etc. Greatly ensure users’ safety.

5.) Easy to operate, can provide operation instruction, pictures and vedios for users.

6.) Compared with heater vacuum separator, ultra-low temperature frozen lcd separator can help you easily solve your headche about bulk volume separating workload and edge screen separating, it can also peel off a lot of OCA, LOCA glue except for SCA glue.

7.) No need to change the polarizer film.

8.) Can keep the backlight (be careful, easily damaged), also can take off the backlight.

9.) High efficiency. No components damage during the LCD module separating process.

Operation Instructions:

1.) Before using, it will take the machine around 30～40 minutes to cool to the set working temperature.

2.) Place the LCD screen on the frozen plate.

3.) Freezing time from 30 seconds to 1 minute depends on different LCD screens.

4.) Take out LCD screen and separate it.

Below is the URL of youtube video link for your reference:

https://www.youtube.com/channel/UCpXgF19dgOMtxk4wz49-yBw

Tips:  

1.) For serious crushed glass, please stick a tape on glass for safety and good for machine

2.) Please make sure the operator wears gloves in case of danger.

3.) It is much easier to separate out the bracket and other components after freezing processing. Please pay attention to the backlight water inlet.

4.) After separating the LCD screen, pay attention to the water treatment and temperature recovery.

5.) When separating the curved screen, the separation risk caused by the temperature difference between 2 sides of the curved surface screen. Please pay more attention to this point.

6.) After LCD separation, please put the glue side upward to avoid sticking on the article surface after the temperature return to the normal.

                                              PRODUCT APPLICATION

Suitable for Photoelectric manufacturers, LCD production enterprises, Mobile phone steel film production enterprises, Mobile maintenance industry, etc.

                   

Super thick heat insulation layer box body + double sealing treatment door, good thermal insulation performance

                   

++

                   

Imported high precision microcomputer temperature controller, precise temperature control

                   

++

                   

 Imported advanced dual-frequency compressor, more stable refrigeration performance

                   

++

MAINTENANCE

◆ Do not place heavy objects on the door or cover of cryogenic refrigerator to avoid compression deformation

◆ When receiving the machine, leave it for 2-5 hours before power on and start up. When using, just press the switch after power on

◆ After starting up, the first three minutes are the compression protection time, and the compressor will start after three minutes

◆ Every once in a while, the cryogenic refrigerator should be cleaned and maintained and dust cleaned